Model: ACP -1300-05

      framework components: steel-panel groove and steel machine chassis, to meet the need of the intensity and rigidity

      Rollers:φ400 mm x 1,500 mm x 3sets

                             We adopt double helix laminas return back to make the steady temperature of the rollers, and the temperature can rise or fall quickly without any cooling set. The surface of the roller quenching, rubbing, mirror polishing chromium plating treatment, then the rigidity can reach above HRC62. The rollers’ surface deviation less than 0.02mm, temperature within±2℃. The gyration connector of hot kerosene and tubes are with heat-resistant and press-resistant.

                   The orientation of rollers: use the exactitude pole elevator and its components. When the centre roller is fixed, then the up and bottom gap motors can be generally regulated, handfine adjustment, and modulated left and right independently. We can adjust quickly andfine adjustmentat the same time. With the high intensity and precision, the improved design is the core centre for the ACP quality.

            The drive motor:2.2kwx 3sets, independently transfer, and can adjust the speed by the material of PE and to improve the quality during the calendaring, glazing and equally extruding of the material.  

      Line speed: 0.4～4 m/min

      Cooling transportation shelf: moulding groove and steel shelf

      Conveying rubber wheel: high-temperature andwear-resistant,φ60mm x 1,500mm x 10sets

型　　號：ACP -1300-05

機械尺寸：1,800L x 2,010W x 2,020H（mm）（大約）

機械重量：2,500 kg（大約）

架構組成：鋼板槽鋼機座，確保強度，剛性的需求。

整平輪組：φ400 mm x 1,500 mm x 3 支

采用雙套管螺旋葉片回路，使輥輪表面溫度均勻，升/降溫迅速，且無需大量冷卻介質。輥輪表面淬火、研磨、鍍硬鉻（鍍層厚度不低于0.10mm）后鏡面拋光處理，硬度達到HRC62以上，輥輪表面跳動小于0.02mm，表面溫度誤差在±2℃以內。附熱媒回轉接頭及耐熱耐壓軟管。

輪組定位：采用精密絲桿升降機及其組件，中央輪固定，上、下輪間隙電機粗調，手動微調并可左右獨立調整。可實現迅速調整間隙和高精度微調同時進行的目的。本機構高強度，高精度，優化后的設計是確保成品板材質量的核心部件。

傳動馬達：電機2.2kw x 3臺，獨立傳動，可根據不同PE料做適度速度調整，使PE芯材壓延，上光，均勻吐料質量顯著提高。

線 速 度：0.4 ～ 4 m/min

冷卻輸送架：成型槽鋼機架

輸送膠輪：高溫耐磨φ60mm x 1,800mm x 10支